Termékek amazonec agyag (24)

- White clay - Black clay - Red clay - Rhassoul clay (Ghassoul) - Blue clay - Pink clay - Green clay - Yellow clay

Latersana Additional compound based on ground "old" bricks and tiles, to be added to mixtures of hydraulic lime and aggregates, for producing mortars, plasters and subbase screeds, similar to the compounds of tradition "cocciopesto" (lime mortar with crushed pottery), in ecological building interventions and in the restoration of vintage buildings and monuments. The reactive capacity, which is beneficial, of the Latersana cocciopesto (lime mortar with crushed pottery) vis-à-vis the components of anhydrous mixtures based on natural hydraulic lime, botticino, and cocciopesto (lime mortar with crushed pottery), is facilitated by the fact that the composition of Latersana mainly consists of antique brick and tile granulates, produced with cooking oven temperatures that did not exceed 1000°C. Thus, the granulate quality was not affected by transforming into a clinkerised, inert product. The addition of Latersana in mixtures of lime and aggregates, promotes the improvement of the watertightness of the system, increases the resistance to compression, improves the workability of the final compound. Production of mortars, screeds and plaster based on natural hydraulic lime, carbonated and cocciopesto aggregates. Add Latersana with the correct mixture of binders and aggregates, in the quantity required for the specific use (between 5% and 20% by weight of the weight of the remaining anhydrous components: hydraulic lime, aggregates, earth colours). Add the required water, mixing thoroughly, until a homogeneous, lump-free mixture is obtained. Variable according to the different design requirements (approximately between 5 and 20% of Latersana on the weight of the anhydrous components of the mixture: hydraulic lime + aggregates + earth colours). Bag 25 kg - Pallet: 60 x (Bag 25 kg)

Une utilisation simple et rapide 1 Installez simplement le PadXpress sur votre lustreuse (2000 tours/minute maximum) 2 Pressez une fois sur la carrosserie pour appliquer du produit 3 Lustrez la surface à traiter quelques secondes 4 Un coup de chiffon et c'est terminé ! Ce traitement permet de déposer un film protecteur céramique sur le véhicule en 30 minutes ! Le véhicule aura été préparé auparavant. À base de nanoparticules de céramique, ce traitement confère une grande résistance aux impacts, coups de portières, projections routières et variations thermiques que la carrosserie peut subir. Ce traitement céramique dispose d'une une très longue durée de vie dés lors que les lavages de la carrosserie sont réalisés à la main sans produit détergent et avec un savon liquide adapté - Le PH NEUTRE de cette solution préserve la peinture et la carrosserie. Un produit fabriqué en France Le PadXpress dispose d’un réservoir intégré pour un rendement maximum. Positionné sur une...

Pepe nero macinato

ISONEM M 03 est un mortier de réparation à base de ciment, il est élastique, étanche et non fissurable. Ce mortier offre une forte adhérence. Modifié avec des additifs polymères et de fibres, c'est un mortier de réparation très résistant dans les applications épaisses et les réparation structurelle.

1-komponentiger Kleb-und Dichtstoff auf Basis von MS-Polymer Verbrauch ca. bei 5 mm x 5 mm Fugen 12-14 Laufmeter pro Kartusche (290 ml).

Gel microbilles sans solvant, salissures fortes Excellentes performances nettoyantes – Parfum orange frais et tonique – Testé sous contrôle dermatologique Pour graisses, lubrifiants, cambouis, hydrocarbures, goudron, poussières freins, peintures fraîches. La texture adhérente du savon gel microbilles AEXALT Orange n’agresse pas la peau et se rince facilement. Le gel laisse un touché doux sur l’épiderme et une discrète odeur citronnée. Idéal dans les ateliers, sur les chantiers, les services de maintenance, en imprimerie, etc. NB : les gels microbilles AEXALT sont formulés avec des abrasifs d’origine naturelle. Réf:SA671 Conditionnement:Pot de 5 L, Seau de 15 L, Seau de 25L Parfum:Orange Ex:AEXALT ORANGE

Référence GCBLANPIN-1KG

Composition: Azote 8% + 10% betaines, 18 acides aminés.

Hergestellt aus wachsfreiem Schellack feinster Qualität, gereinigt und entfärbt (nicht geblichen). Mit dieser füllkräftigen Politur können Sie die schönsten und hochglänzenden Polituren herstellen. Als Streich- und Spritzlack oder für die traditionelle Handpolitur. Artikelnummer: 0001/s

ACIDE ASCORBIQUE EN SEAU DE 1,5 Kg L’acide ascorbique est un acide organique ayant des propriétés antioxydante L’acide ascorbique a les mêmes propriétés que l’ascorbate de sodium L’acide ascorbique est un produit idéal pour la fabrication de la vitamine C liposomale ACIDE ASCORBIQUE EN SEAU DE 1,5 Kg Notre acide ascorbique s'allie parfaitement à notre lécithine de Tournesol pour la conception de la vitamine C liposomale. Notre Acide ascorbique est vendu dans un pot de 1,5 Kg fermé hermétiquement et inviolable État:Nouveau

Grout CR Composite , castable, anti-washout, controlled shrinkage cement mortar, superfluid consistency, based on high-resistance cements, superpozzolanic fillers (MICROSIL 90), polymeric modifiers, shrinkage resistant agents, specific additives, calcium silicate mineral fibres, selected silica aggregates. - Based on of thickened silica fume - three-dimensionally reinforced fibre with mineral and synthetic fibres - Provides high adherence and adhesion - dimensionally stable (shrinkage-compensated) - Provides high stability-physical chemical and resistance to chlorides and sulphates - suitable for underwater castings: it is anti-washout - high strength in terms of hydrostatic positive and negative thrust. Repair and protective coatings of hydraulic structures, marine and underwater structures, and articles in critical situations: harsh chemical-physical, leaching water, marine atmosphere, etc. Filling of formwork for the containment of cast immersed in sea water. In case of underwater application, the installation operations must be carried out within 8-10 hours of cleaning and "fouling" (accumulation and deposits of organic and inorganic particles on product surfaces) removal. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Pour 2/3 of total mixture water in the cement mixer, gradually add the product and the remaining water, until a homogeneous mixture of the required consistency is obtained. For sizable filling thicknesses, greater than 60 mm, Ghiaietto 6.10 (inert washed is selected with a particle size of from 6-10 mm) can be added in a percentage ranging from 20% to 40 %, on the basis of practical requirements. In some particularly demanding cases in terms of the resistance to the "dry-wet" cycle (for example, for the action of the tides) or for chemical attacks particularly strong, it would be advisable to add, in addition to the gravel, even thickened silica fume(MICROSIL 90), and in a variable amount depending on the thickness and construction-related need, to further improve the waterproofing and the mechanical strength of the product. In these cases, please contact our Technical Service. In the case of casts in water, make sure of perfect product hardening before removal of the formwork. Approximately 20,50 kg/m² of Grout CR for every centimetre of thickness to be implemented (approximately 2050 kg per cubic metre). Packaging: 25 kg bag UM: €/kg

Grout 2 HP Grout 2 HP is a pourable, fiber-reinforced mortar, used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. The formulation contains very fine high-strength cements, micro-silicas with pozzolanic activity, aggregates in a rational granulometric curve (0.1 ÷ 1.8 mm), and special antisegregative additives. The product is mixed with 11% - 12% of water, requiring vigorous and prolonged mechanical mixing. The special formulation of Grout 2 HP provides the castings with mechanical strength, fracture energy, exceptional durability, and very high chemical-physical resistance. Grout 2 HP has a workability time of about 60-90 minutes, after which the setting process is triggered, followed by progressive hardening. The plastic and hygrometric shrinkage is extremely low thanks to the presence of Readymesh PM-060 multifilament synthetic fibers, which provide volumetric stability. The performances that make Grout 2 HP unique are: • very high compressive mechanical strengths (> 90 MPa at 28 days), • very high mechanical resistance to bending-traction (> 12 MPa after 28 days), • excellent durability and resistance to chemical attacks. Grout 2 HP is used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. It is particularly suitable for operations where high mechanical performance is required after short curing (compressive strength at 3 days > 60 MPa) and in operations carried out in severe exposure environments (XC - XS - XF), characterized by aggression from sulphates, chlorides, and nitrates. The material can also be used for repairs in anchoring areas subject to high stresses. The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, etc., and suitably saturated with water until reaching the condition of "saturated with dry surface". Adequate roughening of the surfaces by scarifying, sandblasting, etc. is always necessary to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). It is strongly recommended, for optimal performance of site operations, to use a vertical axis mixer with planetary movement or a double horizontal helicoid. The powder is mixed with drinking water to the extent of 11% - 12%, referring to the total weight of the mortar (about 2.75 liters per 25 kg bag) until a homogeneous mixture is obtained. Mixing time: about 4 minutes with a high efficiency mixer. The anchoring can be filled with a single screw pump, for mortars. Pumping must be carried out at a controlled speed to ensure a low working pressure. In case of restorations, the surface must be protected, after application, by polyethylene sheets or anti-evaporation treatments. Packaging: 25 kg bag Unit of Measure: €/kg

Osmocem SCK Fiber-reinforced monocomponent cement mortar, based on hydraulic binders, superprogoline fillers, selected fine aggregates and crystallizing reagent agents, which favor the penetration of the compound into the support. Ideal for low-thickness protective coatings (4 to 10 mm), with high counterweight adhesion. The specific formulation makes this product ideal for coatings in aggressive environments in contact with chlorides and sulphates (sewage systems). Packaging: 25 kg bag UM: €/kg

Protech AC-P Paint based on acrylic resins in aqueous emulsion, for interiors and exteriors, protective lamellar structure which, in addition to having an aesthetic effect, allows maximum filling, transpiration and very high resistance to mechanical and chemical light. The high coverage and expandability make this product extremely easy to apply. The special acrylic resins that compose it allow to obtain a film characterized by a rapid insensitivity to water even during the drying phase, with a consequent reduction of the "snail effect" in the event of atmospheric events. Protective and decorative finish painting of walls, facades, concrete products, plasters, masonry, natural stone, porous substrates in general. For old plasters, pay particular attention to the old pre-existing paints, which must be removed by careful scraping and brushing in order to obtain a healthy and non-friable support; then proceed with the application of Protech Fix AC fixative. When applying on new plasters, it is good practice to insulate the base with acrylic insulator or even better with a white or neutral microemulsion fixative. Avoid windy or cold days when applying. Do not apply on fresh or particularly alkaline substrates, respect a minimum carbonation period of at least four weeks. On large surfaces it is recommended to apply product from the same batch and always proceed wet on wet to avoid signs of recovery. Never operate with temperatures below + 5 ° C. Rainy weather, excessive atmospheric humidity and temperatures below + 8 ° C can greatly compromise drying with the possibility of washing off by rainwater even after several days. . DILUTION (by volume with drinking water) BRUSH 1st COAT: 15% a crossed coat or two coats 12-24 hours apart 2nd COAT: 10%. ROLLER 1st COAT: 10% 2nd COAT: 10%. SPRAY (through specific equipment) 1st COAT: 15/25% 2nd COAT: 15/25%. To avoid filming defects, being resin-based products in aqueous emulsion, the application temperature must be between + 5 ° C and + 35 ° C with relative humidity not higher than 60/70%. Do not apply under the direct action of the sun and wind. Do not apply on fresh or particularly alkaline substrates, respect a minimum drying period of the substrate of at least four weeks. It is also advisable for colored, not to use on large surfaces dyed with different production batches as slight differences between batch and batch are technically possible. Please check the color before application as we will not respond to any disputes regarding the shade of the applied product. From 0.20 to 0.30 liters of Protech AC-P for each square meter of surface to be painted. Pail 14 l

Unisan A composite mortar that is fibre-reinforced, consolidating, dehumidifying, grey in colour and utilised for the structural restoration of crumbling old or monumental masonry. It contains no substances that are potentially harmful to masonry and is composed of NHL 3.5 natural hydraulic lime and hydraulic binders free from soluble salts, along with silicas with pozzolanic activity, selected siliceous-calcareous aggregates, specific shrinkage-reducing agents and resistant alkaline READYMESH fibres that confer high flex-traction whilst increasing the performance of the mortar’s fracture energy. In conjunction with ARMAGLASS STRUCTURA fibreglass mesh, it is ideal for the structural restoration of old walls or crumbling constructions. Construction of plasters and reinforced slabs in interventions of restoration, construction of plaster and dehumidifying coatings with high performance, bedding of bricks and modular elements. The surfaces should be clean and free of any soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition of "saturated dry surface". In the case of structural reinforcing slabs, you will need to proceed with applying an appropriate reinforcing electrowelded mesh, to be fixed with PROFIX, Grout Micro-J, Repar Tix G2 or Syntech IC 55. Pour about 2/3 of the mixing water into the mixer, add Unisan and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 12-14% of the weight of the bag. After mixing is completed wait a few minutes before applying. Apply the product by plastering trowel and brick trowel, or preferably with plastering machine (type PFT model G4). Do not apply in case of direct exposure to sunlight or excessive ventilation. Cure the protection and the prolonged moist hardening, of exposed surfaces. Approximately 15 kg/m² of Unisan for every centimetre of thickness to be implemented (approximately 1500 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Osmocem N gray Cement compound for the preparation, with the sole addition of water, of a waterproofing osmotic coating that can create horizontal and vertical barriers, also suitable in conditions of negative hydrostatic thrust vis-à-vis water permeation in the buildings. Typical uses include waterproofing underground rooms, elevator compartments, garages, basements, tanks, etc. The action of the active components and of the adhesion promoters of Osmocem N, saturated by the reaction the support capillaries, forming a complex system of gel and stable crystals, which results in the best sealing, effective even in conditions of negative hydrostatic thrust, without hindering the breathability of the walls. Osmocem N is compatible for food substances: is certified as suitable for the containment of foodstuffs and drinking water (Certificate no. 02/2010 Laboratorio Analysis Service di Settimo di Pescantina - VR). Osmocem N waterproof test: • Resistance to positive hydraulic thrust, UNI EN 12390/8: water penetration depth with 5 bar pressure = 1-2 mm (*) • Impermeability to negative hydraulic thrust, UNI EN 12390/8 modified (concrete support a / c ratio 0.7): no passage of water with a pressure of 1.5 bar (*) concrete with penetration depth <= 20 mm are considered waterproof. Waterproofing rigid structures and masonry walls underground, buried or in any case subject to water permeation: lift wells, basements, tanks, pipes, tunnels, garages, bridges, reservoirs, areas containing food, etc. in conditions of positive and negative hydrostatic thrust provided they are sufficiently porous and absorbent and free from any waterproofing and / or water-repellent surface treatment, whether chemical (siloxanes, epoxies, polyurethanes, etc.) or natural (wax-up). Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., water repellent treatments in general, etc. conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer, add Osmocem N and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 19-20% (for interventions in the form of a spatula) or 21-22% (for interventions using a brush with long bristles). After mixing is completed wait a few minutes before applying. If applied by brush, roll out two or more crossed coats. Although it is not a specific product for finishing thick coats, it can still be used for these purposes. In these cases, it is appropriate to use a fibreglass mesh Armaglass 160. Approximately 1.7 kg/m² of Osmocem N for each millimetre of thickness to be made. Packaging: 25 kg bag UM: €/kg

Absorbant huiles et hydrocarbures, fioul Absorbe rapidement les taches d’huiles, d’essence, de cambouis, de gras et de peinture. Assure la propreté et la sécurité des sols où il y a la présence d’huile ou autres liquides. Peut absorber jusqu’à 150% de son volume (en fonction de la substance). Également recommandé pour le sol de la cuisine en cas de présence de gras important. Destiné aux professionnels chargés d’interventions nécessitant une absorption très rapide : plombiers, nettoyage des parkings extérieurs et intérieurs, transports des liquides, risque de pollution etc, tous les garages et toutes les stations services, les cuisines de collectivités, les arrêts de bus en ville, les industries… Réf:AB830 Conditionnement:Boite poudreuse 1 L – Carton de 6 Ex:AEXASORB'UIL

Débloque et lubrifie les pièces grippées avec une grande efficacité. Compatible avec tous les métaux. Produit particulièrement mouillant. Il pénètre rapidement entre les surfaces oxydées, disperse la rouille, les salissures et les dépôts divers pour libérer les mécanismes corrodés ou coincés. Laisse un film gras très mince formant une barrière protectrice contre l’eau et l’oxygène. Diminue le frottement entre les pièces mécaniques et les plastiques. Une action prolongée permet d’éliminer les traces de rouille, cambouis, goudron, colle, adhésif, résine ou calamine même brûlée. Protège les métaux sans agressivité vis-à-vis des peintures et caoutchoucs. Chasse l’humidité et assure des contacts électriques parfaits. Appliqué au montage, il assure une protection de longue durée en s’opposant à l’accrochage de la rouille sur le métal. Compatible avec tous les métaux et la plupart des plastiques, peintures, etc. Réf:AO773 Conditionnement:Bidon de 5 L – Carton de 4, Fût de 220 L

Référence GC5892PINFIN-1KG

Référence GCNOIRPIS-25KG

Référence GCNOIRPIN-5KG

Référence GCMOULEPIN-25KG

Référence COLLEFIBRE-5KG